Name: Motogadget m.switch 3 button
Brand: motogadget
Price: 160.0 CAD
Availability: InStock

Vans X Cult Motorcycle Grips - Gum

$33.95

Vans Motorcycle Grips - Gum

What's more classic than a pair of Vans? Now you can have that incredible grip on your handlebars!

Features the classic Vans waffle sole pattern with a subtle domed centre section for improved ergonomics and vibration dampening
125mm in length
Sold in Pairs
Throttle tube NOT included
Available in 1" or 7/8"

Motogadget mo.blaze pin

$63.50

mo.blaze pin

The mo.blaze pin from motogadget – setting new benchmarks for bolt-on turn signals with Power LED technology.

Its tiny dimensions and minimal design make it almost disappear from the vehicle. Due to the IntensiLED® Technology, the emitted light is extremely bright when switched ON and definitely can no longer be overseen. Additionally, the greatest visibility and safety will be ensured by the patented TranzLight® Technology (TLT) with a wide beam angle.

The bolt-on turn signal is ECE approved as a front and rear direction indicator. The aluminum casing is CNC machined and available with an anodized black or mirror polish surface.

Like any other typical LED turn signal, the motogadget turn signal can be operated with load resistors or any of our load-independent flasher relays (m.flash, m.wave, m.stop, m.relay+).

Please order two turn signals for a pair and four turn signals for front and rear use

Advantages

Absolute unique, new design and principle of operation (light control by TranzLight® Technology)
extremely delicate appearance due to the transparent glass body and very small aluminum base
highest luminosity, achieved by state-of-the-art high output LED technology (IntensiLED®)
electronic voltage conditioning by IC-controlled constant power source with 330kHz pulses and safe protection electronics
extremely bright light in radiation direction, highly visible light in nearly all directions

Parts delivered

1x m.blaze pin turn signal w/ M8 thread
M8 nut
Approx. 100 cm connector cable)
Installation instructions

Specifications and features

Total length with thread	38,5 mm
Length without thread	19,5 mm
Biggest diameter	16 mm
Cable length	ca. 100 cm
Weight	ca. 12 g
Installation	M8 threaded bolt
Power consumption	ca. 3 Watt

Vans X Cult Motorcycle Grips - Black

$33.95

Vans Motorcycle Grips - Black

What's more classic than a pair of Vans? Now you can have that incredible grip on your handlebars!

Features the classic Vans waffle sole pattern with a subtle domed centre section for improved ergonomics and vibration dampening
125mm in length
Sold in Pairs
Throttle tube NOT included
Available in 1" or 7/8"

Motogadget m.button

$145.00

m.button

Another innovation from motogadget: the m.button.
It's a big help - in combination with the new m.unit blue, basic, and m.unit v.2 - in reducing 'cable clutter' and simplifying wiring harnesses.

Integrated into the handlebar tube - or any other adequate location - this tiny cylinder will electrically connect all handlebar instruments, switches, and buttons.
Using state-of-the-art bus technology, the m.button digitally processes signals and transmits them to the m.unit over a thin cable.
The electrical consumers will then be switched inside the m.unit.
All control wires are moved into the handlebar. This saves space, weight, labour, and time. A 'must have' for custom bikes with clean-look handlebars.

In simple facts:
a) normally, the operating current (e.g. headlight or turn signals) is transmitted directly via the wiring of the handlebar switches. Due to the high currents, cables with large cross-sections have to be routed from the fuse box to the switch and back to the electrical consumer.
The result: big cable bundles. Definitely, a 'no go' for custom bikes with restricted space or a concealed electrical system.

b) using the m.unit without the m.button, just a thin cable for each switch- or button-controlled feature has to be routed to the m.unit. These cables only carry minute control currents. All high loads and currents are switched directly at the m.unit and transmitted directly to the electrical consumers. This already leads to a significant reduction and simplification of the wiring harness. Here you can see the example of a circuit diagram.

c) using the m.unit blue, basic, or m.unit v.2 in combination with the tiny m.button, you will once again reduce the number of cables that have to be routed! All switches/buttons on the handlebar are connected at the shortest distance possible and concealed inside the handlebar. Consequently, you will have to route only ONE thin cable from the m.button to the m.unit. All loads and currents will be switched directly at the m.unit (see explanations above). A layout reduced to the max! Here you can see the example of a circuit diagram with the use of m.button

The m.button is completely moulded in, making it water-tight and resistant to vibrations.

Specifications and features

The m.button is equipped with connections for
- turn signal, left side
- turn signal, right side
- headlight (low beam and high beam)
- E-starter
- horn
- brake light switch, front brake

m.button – dimensions
Diameter: 12 mm
Length: 25 mm
Cable length: approx. 60 cm
Connecting cable to m.unit: approx. 200 cm
Weight: approx. 30 g

Attention: The only intended use of the m.button is in combination with m.unit blue or m.unit v.2

motogadget mo.switch basic

$155.00

mo.switch basic 3-button

The mo.switch basic is a universal, high-quality push-button control for handlebars with 1 inch or 22 mm (7/8 inch) tube diameter in a simple, elegant design. In combination with an electronic push-button control box (not included), these CNC-made push-buttons can switch all electrical units such as lights, indicators, electric starters, horn and much more.

CNC-milled from billet aluminum the housing is anodized in glossy black. Optionally, the button holder (inlay) is also available with a silver anodized colour. The compact housing is equipped with either two or three pushbuttons. All buttons are always in the direction to the driver.

The two or three buttons per unit are always black. A hidden M4 stainless steel mounting screw clamps the housing securely to each handlebar.

The individual buttons are of high quality, very robust and protected against vibrations and splash water (IP65).

Due to sufficient size and ergonomic pressure point (light, mechanical detent), they allow a safe operation - even when operating with a glove.

A single-wire or two-wire wiring is easily possible by two terminals per push-button. One terminal for ground is already provided internally for single-wire wiring. Cable routing in the handlebars is therefore easy.

In case of possible damage, the single push-buttons are available individually and can be replaced.

The mo.switch basic is of course compatible with all common push-button controls such as the mo.unit blue/basic.

Scope of delivery

mo.switch basic billet housing
2 or 3 push-buttons per unit
Manual