It's the collab you've been waiting for! PCM and Savage Customs have partnered to bring you this piece of art. Our good pal Jamie, over at Savage Customs, has been mixing up Kandy paints and metal flakes. He's laid down this one-off original paint job on a Sporty-style frisco tank. Bolt this onto your current bike to take it up a notch or use this as your starting point for a new project!
What the hell did Jamie do!?
He went to town as he always does! The tank is black with panels of deep orange/red Kandy with a textured effect. It has pearly peach designs and is trimmed with silver flake pin stripping. The tank has an official collab badge painted in peach at the back. As always, Jamie has finished it all off with a polish that makes the paint look as deep as the Mariana Trench!
There is only one of these sweet ladies in existence so don't waste too much time thinking about it!!
About the tank
Low tunnel tank
2.4 Gallon
Mounts easily with front and rear tabs (custom mounting required)
Has a 3/8" NPT petcock bung on the left side and two 1/4" NPT petcock bungs at rear
Uses 1982/later screw-in vented gas cap (not included)
We always suggest lining a new tank as cheap insurance. TheKreem Lining Kitworks great!
Want that timeless "Wassell" styling but don’t want to have to deal with overpaying for a leaky rusty tank at a swap meet? TC Bros. has your solution! The 2 gallon "Wassell" Peanut Bobber Tank.
This tank features a "frisco" style mid tunnel so that the tank sits just right on the backbone of your frame. Un-drilled front and rear universal mounting tabs keep mounting this tank simple. Popular screw-in-style gas cap bung, single 3/8" NPT and dual rear 1/4" NPT petcock bungs give you plenty of options for petcocks and gas caps. You can't go wrong with this classic styled gas tank!
Even though these tanks are pressure tested from the factory. We recommend sealing any custom tank with Kreem Tank Sealer before painting! It is cheap insurance and we use it on every bike that we build. Also, assure the tank is properly isolated so there is no unnecessary stress placed on the tank our mounting hardware when the tank is mounted. We highly recommend using the gas tank mounting kit for proper installation.
This tank does not fit 2004-newer Sportsters as the backbone tube is too large in diameter.
Mid Tunnel Tank dimensions are as follows; Tunnel Width 2 1/8", Length 15 1/2", Depth 2" in the rear, approx. 4" in the front.
v-Factor - Frisco Mount Sportster Style Tank
Regular price
$310.00
Sportster Style Tank
Low tunnel tank
2.4 Gallon
Mounts easily with front and rear tabs (custom mounting required)
Sold in two bung configurations. The first has a 3/8" NPT petcock bung on the left side and two 1/4" NPT petcock bungs at rear
The second configuration has a 3/8" NPT petcock bung on the left side but DOES NOT have the 1/4" NPT bungs
Uses 1982/later screw in vented gas cap (not included)
We always suggest lining a new tank as cheap insurance. The Kreem Lining Kit works great!
2.1 Gallon Narrow Sportster Style Gas Tank with "Frisco Style" low tunnel to let the tank sit high on the backbone. For years, people have been modifying OEM Harley Davidson Peanut Sportster tanks by cutting them in half, narrowing the tank by removing a section of the middle, and welding everything back together. This look is great, but accomplishing this modification on an OEM tank is very labor-intensive. Fear not, for we have your solution at a great price! This tank is 100% brand new construction and has the same shape that is achieved when you modify/narrow an OEM Harley Sportster tank, but without all the work!
The cap bung is set up high (for max fuel capacity) and is a standard OEM Harley cam lock. You can find a chrome gas cap here and a black gas cap here. The 1/4" NPT petcock bung has been placed on the side near the rear of the tank for maximum fuel usage as well. This tank is the highest quality TIG-welded construction and is pressure tested at the factory before shipping. Please see the photos for dimensions.
Even though these tanks are pressure tested from the factory. We recommend sealing any custom tank with Tank Sealer before painting. Use the Universal Mounting Kit for easy install
Drag Specialties Custom Sporty-Style Gas Tank
Regular price
$183.95
Custom Sporty-Style Gas Tank
Steel gas tank features tig welded construction
20" L x 11" W x 8.5" T
Tunnel is 3" deep
Mounting tabs measure approximately 23" center to center
Tanks for fuel-injected modles accept the OEM fuel pump , components and fuel door
Tanks for carborated modles accept 22mm petcocks
All tanks use L96-20 vented fuel caps (sold seperately)
Approximately 3 gallons of fuel
Chrome mounting hardware included
TJ Brutal Peanut Gas Tank for Honda Shadow VT600 VLX 88-07
Regular price
$560.00
Custom Peanut Gas Tank for Honda Shadow VT600 VLX 88-07
This custom madegas tank for the Honda ShadowVLX, aka Honda Shadow VT600 fits your bikes dual backbone perfectly! Includes TJ Brutal Customs gas cap!
This is not a Sporty tank that has been hacked apart, no, this tank sits perfectly on the back of your bike, is made by hand and will last for years to come.
To mount the tank, set the tank on your bike, loosely thread the rear tank mount to the stock rear tank mounting hole. Look at the forward mounting tab, It will be over the hole in your frame that you need to open up to slightly bigger than 3/8". Take the tank off the bike, carefully drill your forward mounting tab hole, and bolt the tank on!
Tank Specs:
16" L, 9.25" W, 8" D
Capacity - Approx. 2.8 gallons+-
Bungs are 1/8" NPT
Vented aluminum cap included
Petcock sold separately
Tanks are not lined. We recommend using Red-Kote!
**Note: To prevent spillage from fuel expansion and vibration, do not overfill, fill within about an inch from the filler neck. We also recommend using T-tape on all plumbing threads. You need to line these tanks. they will rust eventually and then you will be big sad when the gas starts to ruin your sexual 1800$ paint job from the inside out. **
Drag Specialties Custom Sporty-Style Diamond Pattern Gas Tank
Regular price
$246.95
Custom Sporty-Style Diamond Pattern Gas Tank
Steel gas tank features tig welded construction
20" L x 11" W x 8.5" T
The tunnel is 3" deep
Mounting tabs measure approximately 23" center to center
Tanks for fuel-injected models accept the OEM fuel pump, components, and fuel door
Tanks use L96-20 vented fuel caps (sold separately)
Approximately 3 gallons of fuel
Chrome mounting hardware included
Drag Specialties 82-94 2.25 Rubber Mount Tank
Regular price
$290.95
82-94 2.25 Rubber Mount Tank
Heavy gauge steel with reinforced seams
Come complete with extra-strong mounting tabs, and mounting hardware
Petcocks sold separately
Wyatt Gatling - 2.2 Gal Chopper Gas Tank
Regular price
$375.00
2.2 Gal Chopper Gas Tank
The tank uses a screw-in-style gas cap and has threaded ports for 1/4" petcocks.
Even though these tanks are pressure tested from the factory. It is recommended to seal any custom tank with a Kreem Tank Sealer Kit before painting. Also, assure there is no stress on the tank mounting hardware when the tank is mounted.
Dimensions: Top Length: 18" Bottom Length: 17" Rear Width: 4"
Front Width: 4" Rear Height: 3" Front Height: 8"
Front Tunnel Height: 1.5" Rear Tunnel Height: 1.5" Top Tunnel Width: 1-13/16"
Bottom Tunnel Width: 1-13/16" Tunnel Length: 17"
Hap Jones Peanut Tank 2.0 Gallon
Regular price
$369.95
Peanut Tank 2.0 Gallon - Deep Tunnel
Hap Jones 2 peanut gas tank includes a die-cast gas cap and features front and rear tabs welded in place.
Accepts 1/4" National Pipe Thread petcock. *NOTE: Features a deep tunnel. *NOTE: For use with bayonet type die cast scalloped gas cap, early chopper cap we have offered since 1983! *NOTE: Builder must drill a 5/16" hole in each tab for mounting.
Drag Specialities Mustang Tank
Regular price
$241.95
Mustang Tank
Fat Bob style custom application, low-tunnel holds approximately 3.3 gallons
Features a 3/8 NPT-style petcock mount with two 1/4" NPT crossover fittings
Single cap design
Uses 73'-81' style gas cap
Measures 19 3/4" L (including mounting tabs) x 11 1/5" W x 7 1/2" H (approximately)
NOT FOR USE WITH FUEL INJECTED MODELS
We always suggest lining any new tank as a cheap form of insurance. The Kreem Lining kit works great
The Prism Supply Co petcocks are guaranteed for life! If you're having an issue with it you can send it back to them and they will rebuild it for no additional cost!
This unique petcock fits direct to a 1/8 BSP thread on your gas tank. This keeps your gas tank looking very clean. It features a 5/16" diameter hose barb on one end and a fuel filter on the other. We recommend using our 1/4" Fuel Line for a snug, leak-proof fit. Rotating the cylindrical piece with the two grooves is how the fuel is toggled on and off. The fuel line does not rotate while toggling the fuel on/off. No reserve.
Prism Supply Co Petcock 3/8 NPT
Regular price
$170.00
Sale price
$144.00
Petcock 3/8 NPT
The Prism Supply Co petcocks are guaranteed for life! If you're having an issue with it you can send it back to them and they will rebuild it for no additional cost!
This unique petcock fits direct to either a 1/4" or 3/8" NPT bung on your gas tank. This keeps your gas tank looking very clean. It features a 5/16" diameter hose barb on one end and a fuel filter on the other. We recommend using our 1/4" fuel line for a snug, leak-proof fit. Rotating the cylindrical piece with the two grooves is how the fuel is toggled on and off. The fuel line does not rotate while toggling the fuel on/off. No reserve.
Many custom and aftermarket gas tanks use a 1/4 inch NPT or 3/8 NPT petcock. NPT stands for National Pipe Thread and it is a tapered thread that seals as you tighten the petcock into the threaded fitting on your gas tank. Lowbrow Customs makes petcock adapter nuts in both brass and chrome that allow you to adapt your 22mm petcock bung to accept either a 1/4 inch NPT or 3/8 inch NPT petcock.
