Perth County Moto

Complete Performance Carb Rebuild Kit - Honda Shadow VT600 & VT750 - Dual Carb

This Complete Performance Rebuild Kit is the only carburetor rebuild kit that includes literally everything you need to get your carburetors in the absolute best performing condition!
If you pick up one of these rebuild kits you do NOT need a tuning kit as well. 
Your carburetors can be a daunting task and even more so when you don't have the proper parts. That great barn find that has 200 miles on it has been sitting with carbs full of ancient fossil fuels for 15 years and now she's yours. Why mess around with trying to use corroded parts and old rubber seals when you can easily replace them and eliminate these parts as a source of tuning headaches?!?! With this kit you can rebuild your own carbs to better than new condition! 

Does not fit VT700 or VT500 models. 
This kit is intended to work with our velocity stacks and exhaust for VT600 and VT750 carbureted models. This kit may work with other aftermarket intakes and aftermarket exhaust systems that are more free flowing than stock.

Kit contains -

• Float Seats With Filter (dual carb only)
• Float Needles
• ACV Gaskets (dual carb only)
• Stainless Bolt Replacement Kit
• D Bit (single carb only)
• A/F Long Handle Mix Screw (Single - 1 mix screw) (Dual - 2 mix screws)
• Complete Slide Assemblies with New Needles
• Vacuum Plugs
• TJBC Performance Tuning Kit which includes:
• Main Jets (Single - 142, 145, 148, 150) (Dual - 142, 145)
• Pilot Jets (Single - 48, 50) (Dual - 42, 45)
• Needle Shims (Single - 2) (Dual - 4) - 2 per needle
• Click here for our online tuning sheet, complete with carburetor diagram for throttle stage reference!

Our new kits have been upgraded with complete slide assemblies so you wont need to follow the below instructions unless you have one of our older versions of this kit. 

You will need to remove the two plastic retainer rings on your stock slide in order to install the new diaphragms. A small set of dikes is all that's needed to clip them off. Install the diaphragm gently from the top of the slide. Be careful they can tear easily if you muscle them too hard or install them from the bottom. This diaphragm will hold itself in place in the channel at the top of your slide. When re-installing your slides, make sure the vent hole at the bottom of the slide is facing the cylinder head side of the carb. 

Be very careful when installing these diaphragms, they are fragile and soft and can tear very easily.
Once the old diaphragm is removed, install the new diaphragm from the top of the slide don't attempt to shove the thing up from the bottom of the slide. This will guarantee you tear the slide! Use your fingernail to gently push the inner rib into the channel at the top of the slide. again the key word here is GENTLE!

Holey Foot Pegs for Honda Shadows

These foot pegs fit the following models: 

• Fits Honda Shadow VT600 All Years 
• Fits Honda Shadow VLX600 All Years 
• Fits Honda Shadow VT750 1983-1984 
• Fits Honda Shadow VT750 1998 and up 
• Fits Honda Shadow VT1100 models that do not come stock with floorboards. 

The Holey Foot pegs for Honda Shadows are a direct fit for your Honda Shadow! No need for adapters, these foot pegs use the stock mounting hardware and stock mounting clevis for easy installation and a seamless, clean look!  

These pegs do not use the stock springs

3L Lockable Jerry Can and Sissy Bar Mount - Red

TJ Brutal Customs has come up with arguably the best fuel solution we've seen yet! Perfect for long road trips or those small tank blues for daily riders rockin' a peanut tank. 

Not only will it mount to frames, but it includes the TJBC proprietary sissy bar mount which allows you to mount your jerry can on the back of any sissy bar.

• Fits most sissy bars made from 1/2" dia bar (round or square) using the adapter ring. 5/8" bars will not need the adapter ring.
• 3L capacity
• Lockable by key (includes 2 keys)
• Available in Brutal Black or Red
• Solid aluminum mount 
• Doubles as an additional tie-down point
• Rubberized plates prevent scratching or wear of your sissy bar

Backdraft Exhaust - Honda VT750 - 2004 & Up Aero Phantom Spirit

The Backdraft Exhaust for the Honda Shadow VT750 Phantom, Spirit and AERO are an unrestricted exhaust pipe design that allows you to get the most out of your Honda Shadows performance!  Click here for VT600 exhaust. 

As shown in the pictures, this exhaust is cerakoted in a satin black finish and fits the Honda Shadow VT750 models with the plastic engine covers with the exhaust cutaway on the bottom. The pipes are designed to sit closer to the bike to keep your leg away from the pipes when riding. Some riders may find that the rear pipe sits too close to the side cover, we recommend trimming the side cover back using a dremel tool. 

Each set includes hardware.
Does not include exhaust gaskets.
Does not include brass tips.

*WILL FIT- 

• Aero and Phantom VT750 2004 - 2022
• Spirit VT750C2 /C2F 2007 and newer 
• Shadow VT400

*WILL NOT FIT-

• Spirit VT750DCA up to 2007
• All VT750 ACE Models 1998-2003
• All VT750DCA Spirit Models 2001-2007
• All VT750 RS Models 2010-2013
• Honda shadow Steed
• Honda Shadow VT600 or VLX 600 or Steed

If your bike has the plastic right side engine cover like the bike in this video - 04 Up Backdraft , THESE WILL FIT YOUR BIKE.

SPECS:

• 16GA steel tubing
• TIG welded contruction
• TJ Brutal Customs DOM exhaust bosses
• 3/8" thick steel collars

All pipes are handmade and will have minor differences from set to set, being the nature of custom handmade parts. You may see some plating differences and weld differences, but all pipes have been inspected to make sure they will have a long life on your bike. Color change is normal, even when plated as they are single wall exhaust.  

It is up to you to know your local laws and regulations. We cannot advise you on what is legal.  These are open pipes and they are not quiet. While wrapping pipes is a cool look, it will void a warranty

Hand & Tool Wipes

✅  Tough on grease, stains & odors

✅  Gentle on hands, tools & surfaces

✅  Dual sided for effective scrubbing

✅  No dry, cracked skin

Our Heavy Duty Hand & Tool Wipes make quick work of cleaning up even the gnarliest gunk. Dual textured and extra absorbent to pull away oils, paint, and adhesives with ease. Perfect for keeping tools in mint condition and hands citrusy clean. No dry, cracky skin. No residue-y tools and surfaces. Grab a few for the home garage, work truck, or sinkless job site.  72ct pack.

Hand Soap Squeeze Tube

✅  All Natural ingredients

✅  Convenient portable tube

✅  Maximum grease-absorption power

✅  Moisturizing, lime-scented formula

Meet your next dirty squeeze. Made from all-natural bentonite clay, our Heavy Duty dirt-infused pumice soap breaks down oils, grease, and residue like nothing. “Sensitive” types love our coconut and olive oil moisturizers, which keep skin from drying out and cracking. Real lime essential oil leaves your hands smelling like the Caribbean—not chemicals. Keep this squeeze tube (8oz) anywhere you clean up. 

Fingernail Brush

✅  Stiff, durable bristles

✅  Strong suction cup backing

✅  Black bristles look cleaner, longer

You’re not seriously gonna call it a day with all that gunk left under your fingernails? Clean in and around dirt’s favorite hiding spots with this compact scrub brush. It kind of feels like a manicure—ahem, manicure—and gets your filthy fingernails clean enough to eat out of. Strong suction cups let you stick it to all sinks and smooth glass/metal surfaces. Works great on your dirty boots, too.

Ultra HD Countertop Jug

✅  Aggressive, Ultra HD cleaning power

✅  Paint, adhesives, crude oils & more

✅  Solvent-free, waterless hand cleaner

✅  Will not dry out skin - fresh lemon scent

Find yourself elbows deep in the gnarliest gunk known to man without a sink in sight? No problem. Our Ultra Heavy Duty formula lets you easily wipe away paint, adhesives, crude oils, and more with no water needed. Aggressive on gunk but gentle on skin, you’ll love how it keeps even the hardest working hands soft, moisturized, and grime-free. Smells like lemon, so your skin won’t smell like chemicals. Mmm… zesty. Perfect for higher-volume use.

All Natural Countertop Jug

✅  All Natural ingredients

✅  Large long-lasting container

✅  Maximum grease absorption power

✅  Lime essential oil scented

This Heavy Duty mechanic’s soap is tough as mud—because it is mud. Bentonite clay, to be exact. Our coarse pumice formula breaks down grease, grime, and gunk to leave your hands cleaner than a Dad joke. Oh, you’re “sensitive”? Relax. All-natural moisturizing ingredients prevent skin of all types from drying out and cracking. Perfect for the home garage or low-traffic wash stations.

The Bobber - Brown

Goldtop England has created a classic 1970s style leather motorcycle jacket revived for modern-day riders. It comes equipped with CE Level 1 armour in the shoulders and elbows and a pocket for an optional CE Level 2 back protector. The jacket is manufactured from hand-selected, 1.4mm thick aniline cowhides which have each been hand-waxed, making each finished article unique, with a patina that ages beautifully with both time and wear. The whole jacket is finished by hand with a soft tan suede trim, prestige quality zips throughout, and all additional metalware being made from high-quality polished Stainless Steel.

For the best care of your Goldtop Leather jacket, we suggest using Goldtop Vintage Oil

PRODUCT INFO

Canvas Vest

• 20 oz. Heavy Hitter raw canvas
• Preacher Collar
• Bandana paisley Liner
• 4 outside pockets
• Easy access panels for patch work
• traditional club style vest
• 3 panel bandanna liner
• Lifetime warranty on hardware and zippers

Aura Heated Vest

Quilted fitted vest with three heat levels at the push of a button! The vest plugs into a slimline Black Arrow branded power bank that slips into the inside pocket. The power bank can also be used to charge your phone on the go! The wide front placket conceals a waterproof zipper. The vest heats front and back and on the highest setting with a fully charged power bank, you should get around 3 hours of warmth.

To use, simply plug in your fully charged power bank and press and hold the power button on the front of the vest to turn it on. Press the power button one, two, or three times depending on the level of heat needed. The power button colour will change to white for the lowest temperature, blue for mid-range temperature, and red for ultimate warmth!

 TECHNICAL SPECS

• Polyfill vest
• Slimline 10,000mAh USB power bank
• 3 Heat settings with the push of a button
• Outer snap patch pockets
• Back snap tabs for waist adjustment
• Comfortable stretch rib collar

SIZE & FIT

Fits true to size. Designed to wear over a thin layer and under your winter jacket. The perfect stylish transition piece to keep you warm off the bike as well!

LADIES!

Can I just say that I F@$#ing LOVE THESE RIDING PANTS!!!  and I think everyone needs to try these bad boys on and see for yourself.  Love Love Love 'em!!! AND THESE ONES ARE HIGH WAIST WOOT WOOT!

Are you looking for protective, comfortable and stylish riding pants???  It seems like an unrealistic combination, right?

Look no further!  Perth County Moto has partnered with GoGoGearLA to offer their Kevlar Leggings here in Canada!

FEATURES 

Fabric Outer Layer: 100% Abrasion Resistant Polyester Cotton Fabric with 5% Spandex

Fabric Inner Layer: 100% Made Of DuPont™ Kevlar® Fibers, 275gsm Weight, 95% Kevlar with 5% Spandex  FULLY LINED WITH KEVLAR FROM TOP TO BOTTOM - NOT JUST IN THE KNEE AND SEAT AREA

Fabric Inside Protector Pockets: Polyester Cotton Jersey

CE-Approved Removable, Adjustable Knee Protector Pads (Level 1)

Inside Pockets for Hip Protectors (protectors not included) 

Two Outside Front Pockets

Ribbed Decorative Detail on Knees

Machine Washable

The HIGH-WAIST style offers you an additional 2" on the waistband but fit the same as the regular version. 

CAUTION: THE US SIZES 4 - 12 RUN SMALL! DO NOT SELECT A SIZE BASED ON YOUR CURRENT PANT SIZE! All SIZES FROM 14 UP RUN "TRUE TO SIZE" MEANING YOU CAN ORDER THEM BASED ON YOUR REGULAR US PANT SIZE!

PLEASE CONTACT LINDZ AT INFO@PERTHCOUNTYMOTO.COM IF YOU NEED ASSISTANCE WITH SIZING.  WE WANT TO ENSURE YOU GET THE BEST FIT AND ARE HERE TO HELP!  HELPFUL HINT:  I'VE FOUND THE BEST WAY TO DETERMINE THE PROPER SIZE IS TO TAKE YOUR FULLEST MEASUREMENT (HIPS, BUM) AND USE THAT AS YOUR LOWER HIP MEASUREMENT. 

NOTE:  If you are 5'9" & taller the GoGoGear Leggings Long Version is what you need!  These are listed separately on our website.  The size chart runs more true to size so please refer to the size chart and order accordingly.

Warrior Jacket - Black

• light aniline cowhide
• asymmetrical zip scooter style jacket with military patched stitching on shoulder
• double snap collar
• left vent zip, two side pockets, and two interior pockets
• action back, lower zip vent on back, and removable liner for multi season riding

mo.unit blue

Springer Front End Black fits Harley Davidson

Black Harley Springer Front End

Moto Iron has been successful in producing a high quality springer front end that is affordable to all bike builders. With its heavy duty, one piece forged rear legs and beefy 1" diameter front legs, these springers offer a high strength level of quality at a price that cannot be beaten. When viewing next to leading competitors, the differences were easy for us to see why they are the better choice. These Springers will fit most Harley Davidson Big Twins from 1949-Present and 1982-2003 Sportsters with 1" neck bearings. Not for use on Dyna Models.

Unique Features:

• Heavy duty, one piece forged rear legs.
• 1" diameter front legs for improved durability.
• Precision fit bronze rocker bushings for long life.
• TIG welded construction.
• Includes 3/4" axle and spacers for 1984-1999 Harley Wide Glide Wheels
• Zinc plated axle and steering stem to prevent corrosion.
• Triple chrome plated or black powdercoated finishes.  

Fitment Notes:

• These are designed to fit most Harley Davidson Big Twins from 1949-Present and 1982-2003 Sportsters with 1" neck bearings and 3/4" Axle.
• They include a 1" diameter steering stem, 3/4" diameter axle, and wheel spacers.
• The included wheel spacers are designed to fit Harley Wide Glide Wheels from 1984 - 1999. They work with a 11.5" Harley Brake Rotor (84-99), and Springer type brake calipers.  
• To install on 1952-1981 Sportsters, a 7/8" - 1" neck cup conversion kit will be needed. 
• You can run other wheels (Narrow Glide, etc...) but you will need to cut your own wheel spacers in order to do so.
• The top tree accepts 1/2"-20 fine thread risers and the riser spacing is 4.75" center to center (same as OEM Harley Springers) keep that in mind when purchasing handlebars.
• If you want to run Harley OEM style handlebars with 3.5" riser spacing you will need to purchase a riser adaptor kit 

These will not fit the following bikes:

• 2004 & newer Harley Sportsters because of turning radius and fork lock interference
• Dyna wide glide or narrow glide. 
• Yamaha XS650, unless you purchase a conversion kit
• Vintage Triumph Models unless you purchase a conversion kit

The Chimps

Locally made in South-Western Ontario. Almost Oldschool handlebars are all handmade from high-quality stainless steel. Polish them to a chrome-like finish or leave them raw. Also available in black powder coat by request.

• 1"
• 3.5” clamping space 
• 9.75” pullback 
• 10” rise 
• 28.5” total width

Vans Motorcycle Grips - Black

• Features the classic Vans waffle sole pattern with a subtle domed centre section for improved ergonomics and vibration dampening
• 125mm in length
• Sold in Pairs
• Throttle tube NOT included
• Available in 1" or 7/8"
  

JIS Screw Driver Set

If your riding a metric motorcycle then this screwdriver set is a must-have. Stop stripping the screws on your motorcycle. They might look like Phillips heads but they're not!

Add a socket or wrench to the back of this screwdriver and get a little extra leverage for those difficult screws. You can also confidently hit the back of these drivers with a hammer confidently! They have a lifetime warranty!

Each set contains the following:

• 1-JIS style screwdriver-size #1 with a 75mm shaft, perfect for those little screws on handlebar switches, electrics, etc
• 1-JIS style screwdriver-size #2 with a 100mm shaft, our most versatile, great for all carb screws, etc
• 1-JIS style screwdriver-size #3 with a 150mm shaft, fits all those larger screws found on the engine cases and bodywork.
• When you receive your Go fast Innovations JIS screwdriver set and open the box, you will find the best set and maybe the last set of screwdrivers you will ever buy. That’s because JIS screwdrivers fit most Phillips screws too.

Yamaha XS650 Weld On Hardtail Frame

Yamaha XS650 weld-on rigid hard tail frame section. This is the easiest way to make your XS650 into a chopper or bobber. They incorporate 3" of stretch and 5" of ground clearance for a very balanced look and stance that is very rideable. They are designed to use your XS650's stock wheel, tire, spacers, and chain adjusters. They are constructed of 1 1/8" diameter steel tubing with .120" wall thickness. The 1 1/8" diameter is also the same as the stock XS650 frame tubing for a very nice looking install that looks like it was factory made. The axle plates are cut from 3/8" thick steel and have an integrated mount hole for easy fender mounting. The hardtail was designed using the latest CAD software and built in a CNC machined fixture for a perfect fit every time. The lower rails have solid steel slugs welded into them that fit into the stock frame tubes for strength and easy assembly. Mounting instructions are included with every kit.

Only for use with 1970-1983 Yamaha XS650. Can't be used with any other Yamaha or other manufacturer motorcycles.

For all other makes/models, please refer to SKU: 104-0011, Universal Hardtail Kit in our Related Products section.

- High Quality, Proven Design since 2007

- Designed By TC Bros. Using The Latest 3D CAD Software.

- CNC Mandrel Bent American Made Steel Tubing For Accuracy.

- Welded in a CNC Machined Fixture For a Perfect Fit Every Time!

Box Chopper Tail Light

This is the Prism version of the old style "Chopper Box light." It's equipped with a dual function LED cluster that acts as both a brake light and running light. The size of the Prism version housing is 4-1/4" long X 3/4" wide X 2-1/8" in height  while the size of the original style is 4-1/4" long 2" wide and 2" in height. The wires exit through the back of the housing. The housing is made of aluminum which gives you the option for polish, chrome, powdercoat or just leave raw.

All lights come with a two stainless steel 1/4-28 bolts spaced 3.5" apart for mounting.

6" Raw Flat Fender

6" flat profile fenders are among the highest quality you will find. Unlike others on the market, our fenders are actually designed for motorcycle use. This is NOT another re-labeled trailer fender that doesn't fit the profile of a motorcycle tire properly. These fenders feature a 27" diameter (13.5" radius) that follows motorcycle tires made for both 16" and 18" rear wheels. They are proudly made in the USA from heavy duty 14 gauge steel to survive the abuse that hardtail rigid frame choppers and bobbers can provide. They are undrilled for a universal fit allowing you to cut/drill to your custom application. 6" width works great for up to a 140 series tire.

Sportster Style Tank

• Low tunnel tank
• 2.4 Gallon
• Mounts easily with front and rear tabs (custom mounting required)
• Sold in two bung configurations. The first has a 3/8" NPT petcock bung on the left side and two 1/4" NPT petcock bungs at rear
• The second configuration has a 3/8" NPT petcock bung on the left side but DOES NOT have the 1/4" NPT bungs
• Uses 1982/later screw in vented gas cap (not included) 
• We always suggest lining a new tank as cheap insurance. The Kreem Lining Kit works great!
• This Universal Mounting Kit makes it easy to install

AG-401 Battery (4-Cell)

Petcock 1/4" NPT

The Prism Supply Co petcocks are guaranteed for life! If you're having an issue with it you can send it back to them and they will rebuild it for no additional cost!

This unique petcock fits direct to either a 1/4" NPT bung on your gas tank. This keeps your gas tank looking very clean. It features a 5/16" diameter hose barb on one end and a fuel filter on the other. We recommend using our 1/4" Fuel Line for a snug, leak-proof fit. Rotating the cylindrical piece with the two grooves is how the fuel is toggled on and off. The fuel line does not rotate while toggling the fuel on/off. No reserve.

Many custom and aftermarket gas tanks use a 1/4 inch NPT or 3/8 NPT petcock. NPT stands for National Pipe Thread and it is a tapered thread that seals as you tighten the petcock into the threaded fitting on your gas tank. Lowbrow Customs makes petcock adapter nuts in both brass and chrome that allow you to adapt your 22mm petcock bung to accept either a 1/4 inch NPT or 3/8 inch NPT petcock.