Get rid of your bulky air cleaner and show off that H-D Engine! The Prism Supply Co. Darlington Air Cleaners were designed to achieve a clean, classy, and traditional look while maintaining maximum performance. These are beautifully machined from a solid chunk of 6061 aluminum and are available with either a polished or brushed finish. The internal venturi was designed to allow for maximum airflow. The mounting hardware for the cover is installed from the backside and gives that minimal look we all strive for.
With our combination of heavy and fine filtering elements, we can guarantee you’ll be keeping all that unnecessary crud out of your engine. If you ever are in need of a replacement filter element, those can be purchased here.
This compact kit is designed to be used on all H-D engines that use a CV carburetor or factory EFI units (excluding throttle by wire models)
Dimensions are as follows:
5.5” diameter
1.5” total depth
*Some basic jetting/ tuning may be required upon installation to maintain the correct air/ fuel mixture.
Replace the stock chock assembly with these Shorty Choke Knobs to clean up the look of your Honda Shadow.
Single Carb ChokeKnob Will Fit:
1999-2007 VT600, VLX 600, VT400, Steed
2004-2014 VT750 AERO models (2015 and up had EFI)
Dual Carb ChokeKnobs Will Fit:
1988-1998 VT600, VLX 600
1998 and up all dual carb VT750 models- Spirit, ACE,
1983 VT750C (was only available in America for this year)
1984-85 VT750C (was only available in Canada)
1983-86 VT500C
You can pull firmly on the knob and they will lock into place, once locked open let the bike warm-up for a few minutes. To shut off the choke, Press it into its seated position.
These will fit the dual and single carb Honda VLX, VT600, and the single and dual carb VT750, as well as the VT1100 and VTX1300. If your stock air filter box is installed, accessing the choke will be near impossible. These are best paired with the TJ Brutal velocity stack intakes!
TJ Brutal Vacuum Plugs For Single and Dual Carb Shadows
Regular price
$13.00
Vacuum Plugs For Single and Dual Carb Shadows
If you want to remove all the extra hoses and unnecessary lines from your vacuum system, you need these plugs. Otherwise, your carbs will not work correctly.
NOTE- Not all carbs will need a vacuum plug set and some carbs will only use a part of the vacuum plug set.
These boots are a common cause of issues on the Honda Shadow. Eventually, the rubber will dry out and form small cracks that can be hard to find. Causing issues with how the engine runs. You can spend a lot of time troubleshooting and searching for the issue before realizing that it is these boots. If you are removing your carbs and still have the original boots, we suggest changing them.
INSTALLATION TIP! When installing your new intake boot, put a tiny bit of grease on your finger and apply a thin film to the inside surface of both ends of the carb boot and the carb flange. This makes installation a breeze and you won't be fighting friction!
If you're running an open-air intake or velocity stack on your vlx/vt600 or vt750 (dual carb only) then you will need to jet and tune your carbs. This Performance Tuning Kit from TJBC is what you need!
Single Carb Kit Fits:
Honda Shadow VT600, VLX, Steed 1999-2007
Dual Carb Kit Fits:
Honda Shadow VT600, VLX, Steed 1988-1998
Honda Shadow VT750 ACE 1998-2003
Honda Shadow VT750 Spirit 2001-2007
Aren't sure if you need to re-jet or tune your carbs? Simply put, if you've modified and changed your intake or exhaust, you need to re-jet and re-tune your carb(s)
Single Carb Kit Includes:
2 pilot jets - 48, 50
4 main jets - 142, 145, 148, 150
2 brass shims to lift your stock jet needle
1 TJ Brutal Customs Air/Fuel Mix Screw
Dual Carb Kit Includes:
2 sets of main jets - 142, 145
2 sets of pilot jets - 42, 45
4 needle shims
2 Air/Fuel Mix Screws
The screw handle is numbered so you can easily count how many turns in or out you are to make tuning a breeze! These Jet Kits are NOT intended to work with stock intake/exhaust setups this is specifically for open intake and exhaust.
TC Bros. Chrome Louvered Air Cleaner for HD CV Carbs & EFI
Regular price
$105.00
Chrome Louvered Air Cleaner for HD CV Carbs & EFI
Get rid of your bulky "Ham-Can" style air cleaner and show off your V-Twin Engine with this TC Bros. Choppers chrome louvered air cleaner.
Kit features CNC machined, powder-coated steel mounting bracket that is proudly made in the USA. Included mounting hardware fits into recessed holes to provide a proper sealing surface for the included filter element.
Kit includes both a hotrod-inspired Tri-Bar wing bolt and standard round head screw hardware. This ultra-compact kit is designed to fit all Harley Davidson® Big Twin and Sportster models using factory CV Carburetors or factory electronic fuel injection (EFI) units (excluding Throttle by Wire models).
This kit will not fit 1995-2001 HD Big Twin models equipped with Magneti Marelli fuel injection units using dual bore throttle bodies. This kit will also not fit Harley FBW models (a.k.a. Fly By Wire or Throttle by Wire) as commonly found on late model EFI Twincam FLT touring and all Milwaukee 8 engine models (M8 Softail and Touring).
If installing on models using a CV carburetor, it is highly recommended to use it in conjunction with a support bracket for longevity. See TC Bros. SKU #109-0083 for Sportster models. A support bracket is not required on EFI models. Note: EVO Big Twins and 1991-up Sportsters also require crankcase breathers. See TC Bros. SKU #109-0082.
