OG Low Profile LED Tail Light V4 for Harley-Davidson

Name: OG Low Profile LED Tail Light V4 for Harley-Davidson
Brand: Original Garage Moto
Price: 119.95 CAD
Availability: InStock

$119.95

Option

Standard

Without integrated license plate light

Quantity

All Harley-Davidson fitted with a Squareback tail light can use our OG Low Profile LED Tail Light V4 as a direct replacement for better & brighter overall lighting. These function as running and brake lights in the same way the OEM tail light does. They can also be used (or not) in conjunction with the built-in integrated turn signals. Features a very low-profile smoked lens. For models with the plate below the brake light, such as most newer Baggers models, it is also available without an integrated license plate light.

*Comes with a full-year replacement warranty.

Features

Unique Ultra Low profile dark smoked lens
Molded OG Logo on the lens
Integrated blinkers
Function as Run/Brake
New improved Epoxy dual layer Base Coating. Fully waterproof.
New improved 3M Duro Neoprene seal included
New V4 Blackout SMD Ultra Bright LED Board
Dual-function LEDs;

Red running light - Full 54 LED Chip
Bright Red brake light - Full 54 LED Chip
Amber Signal - 19 LED Chip

Optional White license plate LED lighting
Includes OEM connectors - Plug-and-play
Fully warranted

Fitment

Fits 1999 to present Harley-Davidson Models with tail light base plate (Standard & Without integrated license plate light)
Fits 2018 to 2024 Softail Low Rider FXLR/S. To utilise the turn signal function on the tail light, our 18+ M8 Softail Rear Fender Harness is required.
Do not fit 2022-2024 FXLRST models using our new Delphi 3-way variant (Delphi 3-way). These models will need our OG Low Profile LED Tail Light V4 for 2023-Up Softail Lowrider ST
Do not fit 2025 to present Softail models

*For 2022-2024 FXLRST models, you must replace the tail light base plate bezel and circuit board with the following Harley-Davidson part numbers: 68830-99A + 73381-12. This allows compatibility with our OG Low Profile LED Tail Light V4 and the OG 18+ M8 Softail Rear Fender Harness for Harley-Davidson.

**If you're experiencing hyper flashing or bulb-out error code, add our OG LED Load Equilizer for a plug-and-play solution for non-CANbus bikes.

***For offroad use only

Installation

Click here for LED turn signal synchronization instructions

mo.blaze pin

The mo.blaze pin from motogadget – setting new benchmarks for bolt-on turn signals with Power LED technology.

Its tiny dimensions and minimal design make it almost disappear from the vehicle. Due to the IntensiLED® Technology, the emitted light is extremely bright when switched ON and definitely can no longer be overseen. Additionally, the greatest visibility and safety will be ensured by the patented TranzLight® Technology (TLT) with a wide beam angle.

The bolt-on turn signal is ECE approved as a front and rear direction indicator. The aluminum casing is CNC machined and available with an anodized black or mirror polish surface.

Like any other typical LED turn signal, the motogadget turn signal can be operated with load resistors or any of our load-independent flasher relays (m.flash, m.wave, m.stop, m.relay+).

Please order two turn signals for a pair and four turn signals for front and rear use

Advantages

Absolute unique, new design and principle of operation (light control by TranzLight® Technology)
extremely delicate appearance due to the transparent glass body and very small aluminum base
highest luminosity, achieved by state-of-the-art high output LED technology (IntensiLED®)
electronic voltage conditioning by IC-controlled constant power source with 330kHz pulses and safe protection electronics
extremely bright light in radiation direction, highly visible light in nearly all directions

Parts delivered

1x m.blaze pin turn signal w/ M8 thread
M8 nut
Approx. 100 cm connector cable)
Installation instructions

Specifications and features

Total length with thread	38,5 mm
Length without thread	19,5 mm
Biggest diameter	16 mm
Cable length	ca. 100 cm
Weight	ca. 12 g
Installation	M8 threaded bolt
Power consumption	ca. 3 Watt

Motogadget m.blaze edge

$85.00 $70.00

m.blaze edge

The m.blaze edge by motogadget is a 3in1 bolt-on turn signal in a visionary design. It's a turn signal, rear light and brake light in one housing.

Using the motogadget TranzLight® Technology the light of the power LEDs is precisely controlled and emitted. The exclusively developed IntensiLED® System provides the highest and constant light intensity.

The metal housing and the PMMA lens are designed with CAD software by free-formed surfaces.

The cutting-edge design is oriented to modern automotive luminaires and establishes new dimensions in the motorcycle market. The m.blaze edge is available plated in Chrome and Dark-Chrome.

The m.blaze edge has an E-mark as a rear turn signal, as a rear light, and a brake light. The turn signal can be installed like any other LED turn signal with power resistors or all of our load-independent flasher relays (m.flash, m.wave, m.stop, m.relay+).

Please order always a right and a left turn signal when used as a pair.

Parts delivered

A 3in1 turn signal for the rear, left, or right side
M8 thread and nut
4 x 65 cm length of cable
4 cable end clamp
Installation instructions

Specifications and features

Total length w/ thread	92 mm
Length w/o mounting thread	54 mm
Height	20 mm
Weight	55 gr

TC Bros. - Stop Model A Tail Light

$127.00

Ford "Stop" Duolamp Model A Stainless Steel Tail Light

TC Bros. Polished stainless steel 12V Ford "STOP" Duolamp reproduction tail light with red glass lens. Light features both a brake/running light as well as a License plate light to illuminate your plate at night. The two wire hook-up for the brake and tail lights mean this light is self grounding through its housing. The black wire is the 12V positive running light hookup. The green wire is the 12V positive brake light hookup. Light features standard automotive style bulbs (#1156 for Brake Light, and #67 miniature for Running Light). Replacement bulbs are easily sourced from local autoparts stores should you ever require. These lights measure 3 3/4" in diameter, 2 1/4" deep. The mounting studs are 1 3/4" center to center. Great light for your old school bobber or chopper! Note: For best results on high-vibration applications, isolate the tail light mount with rubber grommets.