Vans X Cult Motorcycle Grips - Gum

Torker Grips - White

Diamond pillow surfacing is comfortable but wears like the sole on a boot. No inside flange makes our Torker grip a great choice for aftermarket throttles—clean and lean.

Technical Details

• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• The flangeless design looks great on café racers, vintage Japanese and British customs and modern cruisers
• Thick one-piece moulded end design for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell moulded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1- or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips sufficient time to set up on the bars. Immediately after installation, you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube. 

RECOIL GRIPS - BLACK

Construction: Injection-molded Krayton synthetic rubber

Fitment: Biltwell grips are available in 7/8". These grips are made from the same material used in dirt bike and BMX grips: Kraton Rubber. They are softer and more comfortable but also wear quicker. Just like a dirt bike, plan on changing them often, depending on how hard you ride and in what conditions.

Details: Scroll down for Installation Tips. We recommend using WD-40 to install the grips and suggest letting them dry overnight. Adding a ring of safety wire on each end is a standard moto practice and all of our grips have grooves to accommodate this.

Note: Using Biltwell rubber grips on H-Ds will often require that your motorcycle is equipped with an aftermarket throttle tube (our Whiskey throttle tube, for instance). The grips do not have a built in plastic throttle tube, they are meant to slide over a higher-quality aluminum tube.

Kung Fu Grips - Oxblood

Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.

Technical Details

• Injection-molded Thermoplastic Vulcanizate synthetic rubber is soft, durable and highly UV-resistant
• Medium inside flange cushions rider's hands from rubbing the throttle and controls
• Thick outer flange for durability
• Safety wire grooves for added security
• Aftermarket throttle tube required to install Biltwell grips on stock H-D hand controls—see our Whiskey Throttle

Install Tips

Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell moulded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1- or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation, you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube. 

TBW Throttle Sleeve

Fits 08-19 FLHT/FLHRFLHX/FLTR models and H-D FL Trike, 16-20 Softails, 16-17 FXDLS