🚚 Free Canada-wide shipping on orders over $199 (excluding oversized items)
New: Now also with 3 push-buttons per unit.
The m.switch is a high-quality universal push-button control for handlebars with 1 in. or 22 mm (7/8 in.) tube diameter in a plain and elegant design.
These finely CNC machined hand controls in combination with an electronic push-button control unit (not included in the kit) are used to operate all electrical features, e.g. lights, turn signal, E-Starter, horn, etc.
The casing is made from CNC machined billet aluminum and is available in mirror polished or reflective black finished surfaces respectively.
The compact design casing permits mounting two or more units on one handlebar.
Each unit is equipped with two or three push buttons in black or stainless steel. Different looks matching or contrasting the casing can be combined freely. Two flush built-in M5 stainless steel mounting screws (only one screw on the three-button version) ensure secure and stable clamping of the push-button control to all handlebars.
The push-buttons are of high quality, very robust design and vibration- and spray water-proof (IP65). The adequate size and ergonomic pressure point (easy, mechanical detent) provide for a definite actuation sensing - even when operated with gloves. This feedback allows shifting without the need to check the operation.
Each push-button is equipped with two terminals for an easy optional circuit layout with only one or two cables. The internal ground terminal is already provided for the 'one cable layout'. Therefore, the routing of the cable inside the handlebar can be performed easily.
The push buttons are available separately and can be replaced if damaged. The m.switch is of course compatible with all common push-button controls, e.g. the m-Unit.
Motogadget mo.unit Blue - Digital Control Unit & Wiring System for Custom Motorcycles
Regular price $570.00🚚 Free Canada-wide shipping on orders over $199 (excluding oversized items)
The Motogadget mo.unit blue is the ultimate digital control and wiring solution for custom motorcycles, bobbers, cafe racers, and choppers. This compact, intelligent control unit replaces traditional fuse boxes, relays, and complex wiring harnesses with a single, programmable digital system that's configured wirelessly via Bluetooth.
📄 Download mo.unit blue Installation Manual (PDF) — Complete wiring diagrams, setup instructions, and configuration guide.
For the latest firmware updates and additional support, visit Motogadget's Support Page.
Complete your mo.unit installation with these essential accessories:
Universal fitment for custom motorcycle builds. Works with 12V electrical systems. Compatible with Motogadget instruments (mo.view, mo.scope), lighting (m-blaze, m-tri), and controls (m-switch, m-button). Ideal for:
Note: For a complete plug-and-play installation, we recommend adding the m.unit Cable Kit and mo.unit Ground Distributor to your order.
Made in Germany by Motogadget—precision engineering for custom motorcycle builders who demand the best.
Motogadget m.unit Cable Kit
Regular price $115.00🚚 Free Canada-wide shipping on orders over $199 (excluding oversized items)
The Motogadget m.unit Cable Kit is the purpose-built wiring kit for building a clean, professional harness with the Motogadget mo.unit blue or mo.unit basic. It contains 17 colour-coded, top-grade copper-strand cables in three gauges — matched to the mo.unit’s output functions — along with cable ties and end sleeves. Approximately 1 kg of materials in total.
Each cable colour corresponds to a specific function or output on the mo.unit system. Having the correct gauge and colour from the start eliminates guesswork, reduces wiring errors, and produces a harness that’s easy to trace and service later. The lengths are sufficient for most custom motorcycle builds.
| Cable Colour | Gauge | Length |
|---|---|---|
| Brown | 2.5 mm² | 5 m |
| Black | 2.5 mm² | 4 m |
| Blue | 2.5 mm² | 2 m |
| White | 1.5 mm² | 4 m |
| Red | 1.5 mm² | 2 m |
| Yellow | 1.5 mm² | 4 m |
| Orange | 1.5 mm² | 4 m |
| Green | 1.5 mm² | 2 m |
| Purple | 1.5 mm² | 2 m |
| White | 0.5 mm² | 2 m |
| Blue | 0.5 mm² | 2 m |
| Red | 0.5 mm² | 2 m |
| Yellow | 0.5 mm² | 2 m |
| Green | 0.5 mm² | 2 m |
| Orange | 0.5 mm² | 2 m |
| Purple | 0.5 mm² | 2 m |
| Brown | 0.5 mm² | 2 m |
Pair this cable kit with the Motogadget mo.unit blue and the mo.unit Ground Distributor for a complete, clean wiring solution.
Motogadget mo.blaze pin LED Turn Signal
Regular price $69.00🚚 Free Canada-wide shipping on orders over $199 (excluding oversized items)
The motogadget mo.blaze pin sets a new benchmark for bolt-on LED turn signals. Its ultra-compact dimensions and minimal design let it nearly disappear into the bike — until it's on. Powered by IntensiLED® technology, the light output is extremely bright, and the patented TranzLight® Technology (TLT) delivers a wide beam angle for maximum visibility and safety in all directions.
ECE approved for use as both a front and rear direction indicator. The CNC-machined aluminum housing is available in anodized black or mirror polished finish.
Compatible with load resistors or any motogadget load-independent flasher relay (m.flash, m.wave, m.stop, m.relay+).
Note: Sold individually. Order 2 for a pair (front or rear), or 4 for full front and rear use.
| Total length (with thread) | 38.5 mm |
| Length (without thread) | 19.5 mm |
| Largest diameter | 16 mm |
| Cable length | ~100 cm |
| Weight | ~12 g |
| Mounting | M8 threaded bolt |
| Power consumption | ~3 W |
| Approval | ECE (front & rear) |
| Housing | CNC-machined aluminum |
| Finish options | Anodized black / Mirror polished |
Antigravity - AG-801 Battery (8-Cell)
Regular price $310.95 Sale price $302.95🚚 Free Canada-wide shipping on orders over $199 (excluding oversized items)
At a very small 4.25″ Length x 2.25″ Depth and 3.75″ Height (to the top of the terminals) this battery offers extreme power in the most compact size in Lithium Motorsport batteries. This battery is best used for applications where extreme weight loss and ultra compact size are desired and can be used for bikes from 600cc street use and 1200cc race use.
Motogadget mo.switch basic 3-Button Handlebar Switch
Regular price $165.00🚚 Free Canada-wide shipping on orders over $199 (excluding oversized items)
The Motogadget mo.switch basic 3-button is a CNC-milled billet aluminum push-button switch housing for motorcycle handlebars — designed for custom builds where clean, minimal controls are the goal. The 3-button version adds a third control input over the 2-button model, giving you more switching options for lights, indicators, horn, starter, or auxiliary functions — all from a single compact housing.
Available in Black Anodized and Silver Anodized finishes, in both Left and Right handlebar configurations. Fits both 1" (25.4mm) and 7/8" (22.2mm) handlebar diameters and integrates directly with the Motogadget mo.unit wiring ecosystem.
Important: The mo.switch basic requires a compatible electronic push-button control box to function (such as the mo.unit blue or mo.unit basic — sold separately). It does not operate standalone.
Select the version that corresponds to which side of your handlebars you’re mounting the switch on. Left mounts on the left bar (typically controls horn, indicators, and auxiliary functions). Right mounts on the right bar (typically controls lights and starter). All buttons face the rider regardless of side.
Builders and riders running the Motogadget mo.unit system on cafe racers, scramblers, trackers, or bobbers who need three switching inputs from a single housing. Pairs directly with the mo.unit blue or mo.unit basic for a complete, integrated wiring solution.
