ELECTRICAL

Replica Spot Lamp Switch

This is a Replica spot lamp switch set for 1938-1963 spot lamp units.

• Set of 2
• Fits: EL 1938-1940 FL 1941-1963

SILVER series: 8-step 6V 4A / 12V 3A sealed battery saving charger & maintainer

OptiMate 5 6V/12V the smarter charger for all 6V and 12V lead-acid batteries – great for deep cycle batteries!

Fully automatic multi-step program brings the battery safely to full charge – Connect to the battery and OptiMate 5 6V/12V does the rest, no supervision required!

MORE FEATURES:

Automatically adjusts current to match battery size and condition.

Safe to leave connected. Full electronic protection.

Maintains battery at full charge and good health.

Saves your ‘dead’ battery from as low as 0.5V.

Tests battery state of health.

Voltage safety check: will not charge if battery voltage does not match selection. Requires user confirmation.

Energy saving technology. √ Stand-by power less than 0.5W. √ Efficient 24-7 battery maintenance.

Weatherproof. Rated for use down to -40°C / -40°

IDEAL FOR: STD, AGM, GEL, SLI & DEEP CYCLE 6 & 12V batteries from 3 – 120Ah (up to 160Ah for 6V).

CHARGING AMPS: 4A (6V) / 3A (12V) (Ampmatic)

CHARGING VOLTS: 6V range: 0.5V – 7.2V; 12V range: 8V (0.5V*) – 14.4V

*Voltage safety check. Will not charge if battery voltage does not match selected voltage. User must confirm it is a low volt 12V battery > press selection button for 3 seconds to confirm > then lowest charge voltage for 12V is reduced to 0.5V.

OPERATION: Selectable

STEPS: 8

FEATURES: SAVE & CHARGE all 6V & 12V lead-acid batteries.

USE: Indoor / Outdoor  (lowest temperature: -40°F / -40°C).

INPUT: Global (100-240V 50-60Hz), high efficiency (CEC listed).

STYLE: Weatherproof case with wall mounts, with 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector.

SAVE : Low Volt Start of 0.5V + 2 step desulphation recovery.

SAFE: No risk of overcharging. Totally safe for vehicle electronics. Sparks suppressed. Safe for long-term battery maintenance. Automatic shut-down if short-circuited or battery disconnected.

INCLUDED: weatherproof battery lead & battery clip set.

WARRANTY: 3-year limited replacement warranty.

Auto-Resetting Circuit Breaker Kit

This Auto Resetting Circuit Breaker Kit consists of an AT0 inline fuse holder and auto-resetting, 10 amp blade circuit breaker. The wire is not included but can be purchased here

The way this fuse holder is designed eliminates the need for any soldering or crimping, requiring very little tooling to install. 

Some advantages of using our circuit breaker kit over a fuse are below:

• The circuit breaker auto resets after tripping, eliminating the need to ever replace a fuse
• The circuit breaker is more sensitive than a fuse, which causes it to trip quicker. 

mo.blaze tens4 

xs650 Headlight Mounting Bracket

TC Bros. Yamaha XS650 Headlight Bracket. This bracket is designed to work with most aftermarket/custom headlights. The kit comes with metric mounting hardware. Bracket bolts directly to your stock triple clamp. Fits 74-83 models.

Made in USA

Posi-Tap 20-22 awg

Easily the best line of products to make electrical jobs easy and simple

• Taps wires without cutting
• Total wire integrity is maintained
• Installs in seconds by hand
• No crimping or tools required
• Reusable or permanent
• Less resistance
• Vibration-proof
• Fully insolated
• 6-pack

Universal Bobber Tail Light

• Features die-cast construction with chrome finish
• 12v dual-filament tail/brake light with red lens; uses 1157 style bulb
• Requires custom mounting, hardware included
• Measures approximately 2 1/8" diameter and 3" long body
• ECE compliant (not DOT compliant)

LED Tomb Stone Tail Light With License Plate Bracket

• Chrome housing with red lens and top tag light
• Includes top license plate mount
• Lens measures 4 5/8" x 2 1/2"
• Dual function LED
• 4.5" on centre mounting holes
• Not DOT or ECE compliant

50's Style Bullet Taillight - Chrome

• Features die-cast construction with a 12V dual-filament bulb
• Smooth contour matches most rear fenders
• Comes with license plate mounting tab
• Not DOT or ECE compliant

50's Style Bullet Taillight - Black

• Features die-cast construction with a 12V dual-filament bulb
• Smooth contour matches most rear fenders
• Comes with license plate mounting tab
• Not DOT or ECE compliant

Diamond-Style 5 3/4" Headlight - Black

• Modern features with classic styling
• Bottom-mount design; includes matching finish mounting block
• Available with smooth housing and visor bezel
• Clear lens with H4 bulb
• DOT compliant

Side-Mount Headlight Bracket

If you're building a cafe racer, scrambler, brat or any other style of a motorcycle with a side-mounted headlight then these are the brackets you need.

• Chrome clip-on style headlight brackets that fit all popular forks
• 5.5" brackets fit tube-type custom front ends without headlight provisions, such as custom triple trees and competition forks
• Use with side-mount headlights
• Sold in pairs

Ford Duolamp Model A Stainless Steel Tail Light

TC Bros. Polished stainless steel 12V Ford Duolamp reproduction tail light with red glass lens. The light features both a brake/running light as well as a License plate light to illuminate your plate at night. The two-wire hook-up for the brake and tail lights means this light is self-grounding through its housing. The black wire is the 12V positive running light hookup. The green wire is the 12V positive brake light hookup. Light features standard automotive-style bulbs (#1156 for Brake Light, and #67 miniature for Running Light). Replacement bulbs are easily sourced from local auto parts stores should you ever require. These lights measure 3 3/4" in diameter, 2 1/4" deep. The mounting studs are 1 3/4" center to center. Great light for your old school bobber or chopper! Note: For best results on high-vibration applications, isolate the tail light mount with rubber grommets.