You may also like
The TJBC Mohawk Long Rear Fender for Rear Tires is great for getting that bobber or chopper rear-end look for your Motorcycle! Hand spun from 13 ga steel, this is a fender built to last! These hand-made fenders fit a 150-180 tire, depending on the brands tire profile, the fit may be more snug than others.
Dimensions:
This fender does not include any hardware.
These rear fenders require some fabrication to mount as they do not have any holes pre-drilled, so break out the welder and hood!
These are approx. 7.5" wide and 43" long and when mounted to a stock frame they extend a few inches past 12 o'clock on your wheel.
They fit the rear wheel like a glove and are strong enough to carry a passenger.
The easiest way to set these up on a Honda Shadow VT600 that has been hard-tailed if you are going to make your own struts with the TJBC DIY Builders Motorcycle Fender Strut Kit Lay a length of bike chain or thick tubing, down the center of your tire to set fender height. You can use angle brackets welded to the swing arm or our Pressio fender mounting kit. Drill holes in fender to bolt fender to angle brackets or Pressio kit. Drill 5/16' hole in axle plate. Tap with 3/8-16" tap. Bullet bungs get welded to top of struts and countersunk bungs get welded to bottom of the struts (cut struts to desired length). Cap head bolt goes into countersunk bung into axle plate and bullet bung gets bolted to fender from inside fender.
TJ Brutal Honda Shadow Solid Handlebar Riser Bushings
Regular price $55.00These solid handlebar riser bushings fit all bikes with a 34mm riser pocket in the top tree. These will work with the stock Honda Shadow handlebar risers, as well as with aftermarket handlebar risers. In some cases if you drill out the stock metal bushings inside the Honda Shadow top clamp, you will be able to mount aftermarket handlebar risers or Harley risers in your top clamp!
Includes:
Some people may need the lower bushings some may not, enough people gave feedback that they would be helpful so we decided to make sure you have what you need!
These do not replace the stock rubber bushings that are permanently in your top tree, they replace the removable rubber bushings under the risers.
Please pull your risers off to make sure you have a 34mm pocket. some models of VT750 and VT1100, VTX and other shadows did not have this pocket.
ONLY ONE SET NEEDED TO STABILIZE YOUR RISERS
Your Honda Shadow stock top clamp has rubber riser bushings that get mushy over time and your bars can flex pretty bad. This leads to poor handling and a dangerous situation when you need to handle your bike quickly to avoid a collision. The solution to this is to use these solid riser bushings for a positive connection between bars and front suspension.
NOT NEEDED FOR HONDA SHADOW AERO YEARS 2005-2007
TJ Brutal Customs Shorty Choke Knob - Honda Shadow VT600, VLX & VT750 VT500
Regular price $64.99Replace the stock chock assembly with these Shorty Choke Knobs to clean up the look of your Honda Shadow.
Single Carb Choke Knob Will Fit:
Dual Carb Choke Knobs Will Fit:
You can pull firmly on the knob and they will lock into place, once locked open let the bike warm-up for a few minutes. To shut off the choke, Press it into its seated position.
These will fit the dual and single carb Honda VLX, VT600, and the single and dual carb VT750, as well as the VT1100 and VTX1300. If your stock air filter box is installed, accessing the choke will be near impossible. These are best paired with the TJ Brutal velocity stack intakes!
TJ Brutal Vacuum Plugs For Single and Dual Carb Shadows
Regular price $13.00If you want to remove all the extra hoses and unnecessary lines from your vacuum system, you need these plugs. Otherwise, your carbs will not work correctly.
NOTE- Not all carbs will need a vacuum plug set and some carbs will only use a part of the vacuum plug set.
TJ Brutal Customs Carb Intake Boot Replacement Kit
Regular price $32.56These boots are a common cause of issues on the Honda Shadow. Eventually, the rubber will dry out and form small cracks that can be hard to find. Causing issues with how the engine runs. You can spend a lot of time troubleshooting and searching for the issue before realizing that it is these boots. If you are removing your carbs and still have the original boots, we suggest changing them.
INSTALLATION TIP!
When installing your new intake boot, put a tiny bit of grease on your finger and apply a thin film to the inside surface of both ends of the carb boot and the carb flange. This makes installation a breeze and you won't be fighting friction!
Dual Carb Kit Will Fit:
1988-1989 VT600C SHADOW VLX 600
1991-1997 VT600C SHADOW VLX 600
1993-1998 VT600CD SHADOW VLX DELUXE
1998-2000 VT750C SHADOW ACE
1998-2001 VT750CD SHADOW ACE DELUXE
1998-2001 VT750CD2 SHADOW ACE DELUXE
2002-2003 VT750CDA SHADOW ACE DELUXE
2002-2003 VT750CDB SHADOW ACE DELUXE
2002-2003 VT750CDC SHADOW ACE DELUXE
2002-2003 VT750CDD SHADOW ACE DELUXE
2001-2002 VT750DC SHADOW SPIRIT 750
2003; 2005-2007 VT750DCA SHADOW SPIRIT 750
2003; 2005-2007 VT750DCB SHADOW SPIRIT 750
1989-1990 XL600V TRANSALP 600
SOLD AS A PAIR - YOU WILL RECEIVE 2 BOOTS WITH 4 CLAMPS
Single Carb Kit Will Fit:
TJ Brutal Customs 3L Lockable Jerry Can and Sissy Bar Mount - Black
Regular price $221.95TJ Brutal Customs has come up with arguably the best fuel solution we've seen yet! Perfect for long road trips or those small tank blues for daily riders rockin' a peanut tank.
Not only will it mount to frames, but it includes the TJBC proprietary sissy bar mount which allows you to mount your jerry can on the back of any sissy bar.