The Complete Hardtail Kit provides you with everything you need to ditch that rear suspension and make your vlx/vt600 into a true hardtailed motorcycle
Electronics Tank - Bolt-on E-Tank for VT600 (includes coil mounts)
If you want to take your Honda VLX from hella weak to chopper chic, then you want to run a hardtail setup. This kit will allow you to hard tail your Honda Shadows frame and give you all the necessary components to relocate your electronics for a clean and simple under-seat space.
Exhaust Baffles for 1.75" Exhaust
Regular price
$16.95
Exhaust Baffles for 1.75" Exhaust
These baffles are easily installed on any straight tip exhaust pipes. They are approximately 4" long. Each baffle is sold individually.
These baffles fit the straight cut versions of our exhaust models :
Magnus V Upsweep Exhaust - Honda Shadow VT600 VLX600
These baffles install in only minutes using the included hardware. To install measure how far in you want the baffle to be, and drill a small hole to bolt the baffle in. EASY!
Builders Exhaust Kit for Honda Shadow VT600 VLX 600
You've got a vision for your vt600 but you just can't find the exhaust that stacks up to your creation. It can only mean one thing. It's time to roll up your sleeves and get your hands dirty making your own. This kit is made specifically for the Honda Shadow vt600 and vlx600
Fits Honda Shadow VT600, VLX & Steed 1988 - 2007
This Kit Contains 1.75" OD Mild Steel 16ga Exhaust Tubing:
Qty 2: 20" Straight Tubing Section
Qty 2: 45 Degree Bends 2.5" Radius
Qty 2: 90 Degree Bends 2.5" Radius
Qty 1: 2.5" Radius U-Bend
Qty 4: Exhaust Flange Nuts
Qty 4: Exhaust Flange Nut Aluminum Spacers
Qty 1: VT600Builders Exhaust Boss and Collar Set (Fits years 1988 - 2007)
This kit requires fabrication. As with all our builders' parts the use of these parts is completely up to you and we are unable to give any fabrication advice.
Kustom Tech Rebuild Kit for Clutch and Brake Master Cylinder
Regular price
$53.02
Rebuild Kit for Clutch and Brake Master Cylinder 14mm (9/16") Bore
Rebuild kit for brake master cylinder 14mm (9/16”) bore
MID-USA Spool Wheel
Regular price
$372.95
Spool Wheel
Modern version of an old school classic
21" x 2.15" is a great choice when using any custom springers
3/4" sealed bearings
These wheels have no brake rotor flanges
Custom wheel spacers must be used, depending on your application
Black Hub & Rim - Chrome Spokes
Hardbody Indian Leaf Spring Style Springer
Regular price
$1,736.95
Indian Leaf Spring Style Springer
Designed after the legendary Indian motorcycles from years gone by. This Leaf Spring style springer will make any custom motorcycle stand out in a crowd.
Fully assembled with in-line top bracket without built-in rake (0)
The standard length, (20" measure from the bottom of the lower tree, to axle center) is comparable to a vintage FL model fork length
1" O.D. steering stem designed for Timken type neck bearings
Riser mounts are 4 3/4" centers and threaded 1/2-20
Use part number 36652 neck cup conversion kit to install on K model and Sportster 1952-1981
Includes 3/4" O.D. axle
TC Bros Air Cleaner/Carb Support Bracket For 84-88 EVO Big Twin
Regular price
$92.00
Air Cleaner/Carb Support Bracket For 84-88 EVO Big Twin
TC Bros. Air Cleaner/Carb Support Bracket for 1984-1988 Evo Big Twin
TC Bros Air Cleaner/Carb Support Bracket For HD Twin Cam Engines
Regular price
$92.00
Air Cleaner/Carb Support Bracket For HD Twin Cam Engines
TC Bros Air Cleaner/Carb Support Bracket for HD Twin Cam Engines. Fits all 1999-UP Carburetor models. (not needed on EFI models)
It's the collab you've been waiting for! PCM and Savage Customs have partnered to bring you this piece of art. Our good pal Jamie, over at Savage Customs, has been mixing up Kandy paints and metal flakes. He's laid down this one-off original paint job on a Sporty-style frisco tank. Bolt this onto your current bike to take it up a notch or use this as your starting point for a new project!
What the hell did Jamie do!?
He went to town as he always does! The tank is black with panels of deep orange/red Kandy with a textured effect. It has pearly peach designs and is trimmed with silver flake pin stripping. The tank has an official collab badge painted in peach at the back. As always, Jamie has finished it all off with a polish that makes the paint look as deep as the Mariana Trench!
There is only one of these sweet ladies in existence so don't waste too much time thinking about it!!
About the tank
Low tunnel tank
2.4 Gallon
Mounts easily with front and rear tabs (custom mounting required)
Has a 3/8" NPT petcock bung on the left side and two 1/4" NPT petcock bungs at rear
Uses 1982/later screw-in vented gas cap (not included)
We always suggest lining a new tank as cheap insurance. TheKreem Lining Kitworks great!
Limited Edition. The perfect gift for you or someone else! These illustrations are done on solid wood panels that will look great around the house, office, or shop.
8" X 10"
CLOSEOUT Rolling Chaos Wooden Illustration Panel
Regular price
$30.00
Sale price
$20.00
Rolling Chaos Wooden Illustration Panel
FREE PIN WITH ROLLING CHAOS PURCHASE
Limited Edition. The perfect gift for you or someone else! These illustrations are done on solid wood panels that will look great around the house, office, or shop.
8" X 10"
TJ Brutal Peanut Gas Tank for Honda Shadow VT600 VLX 88-07
Regular price
$560.00
Custom Peanut Gas Tank for Honda Shadow VT600 VLX 88-07
This custom madegas tank for the Honda ShadowVLX, aka Honda Shadow VT600 fits your bikes dual backbone perfectly! Includes TJ Brutal Customs gas cap!
This is not a Sporty tank that has been hacked apart, no, this tank sits perfectly on the back of your bike, is made by hand and will last for years to come.
To mount the tank, set the tank on your bike, loosely thread the rear tank mount to the stock rear tank mounting hole. Look at the forward mounting tab, It will be over the hole in your frame that you need to open up to slightly bigger than 3/8". Take the tank off the bike, carefully drill your forward mounting tab hole, and bolt the tank on!
Tank Specs:
16" L, 9.25" W, 8" D
Capacity - Approx. 2.8 gallons+-
Bungs are 1/8" NPT
Vented aluminum cap included
Petcock sold separately
Tanks are not lined. We recommend using Red-Kote!
**Note: To prevent spillage from fuel expansion and vibration, do not overfill, fill within about an inch from the filler neck. We also recommend using T-tape on all plumbing threads. You need to line these tanks. they will rust eventually and then you will be big sad when the gas starts to ruin your sexual 1800$ paint job from the inside out. **
This bolt-on battery box for the AG801 small case 8 cell Antigravity battery is the perfect fit for yourHonda Shadow bobberbuild! You can bolt these on anywhere they will fit on your bike! Made of .125" (1/8") thick steel, this battery box is built for a long life. Two drain holes in the bottom ensure that any moisture that's collected can get out. I know many of you Shadow owners don't have access to a welder, but almost anyone can get their hands on a simple drill and some bolts!
Specs:
1.25" thick mild steel
Approx 4.5" Length x 2.5" Width x 3.75" Height
3/8" mounting holes
drain holes
This battery box will work great if you are getting rid of all your stock electronics and using one of the TJ BrutalBolt-on E Tanks!! The battery box easily bolts in by drilling 2 holes in the forward tube of your swingarm, all the way towards the right side of the bike, away from the chain. Then attaching the box with 2X 3/8"-16 bolts. Be sure to use loc-tite or locking agent on the threads.
This fits a Honda VLX VT600 88-07 but may fit other bikes. For other bikes, you would need to check the specs for fitment compatibility.
Antigravity 8-Cell Battery Box Approx- 4.5" Length x 2.5" Width x 3.75" Height approx (to the top of the terminals). This box is for the Antigravity 8-cell small case batteries, not for OEM batteries.
